As10 Adhesive Remover From Paintstripper.com

VERSION 1 AUGUST 2018 FORM 34
PRODUCT CODE: R102/A
AS10 ADHESIVE REMOVER

OVERVIEW
Paramose AS10 is an advanced blend of water washable polar and non polar solvents containing thickening agents,evaporation retardants and stabilisers that have beenspecially formulated to remove hard wearing paints andcoatings from substrates.
Paramose AS10 quickly and effectively removes :
•
graf.ti

•
automotive paint

•
two pack lacquers

•
heat resistant .nishes

•
powder coatings

Due to its thicker formulation, Paramose AS10 is ideal for use on vertical surfaces. It is particularly suitable for use inwarmer climates due to its specially designed evaporation retardants. Used by professionals on:

•
cars

•
masonry

•
wood

•
motorbikes

•
machinery

•
.oors


BENEFITS
•
Powerful and effective stripper

•
Fast acting

•
Cost effective

•
Removes most paint, adhesives and lacquered .nishes

•
Removes multiple layers at a time

•
Concentrated for a high performance

•
Non Flammable

•
Non Caustic


SURFACE PREPERATION
Always test a small hidden portion of the substrate before use, to ensure the .nal result is satisfactory and to calculate consumption.
Protection should be provided for areas you do not wish tostrip.
PRODUCT CHARACTERISTICS

Colour Clear
Odour DCM
Form Light Gel
Speci.c Gravity @ 25ºc 1.01
PH 11
Application Temperatures Minimum +5ºC Maximum 30ºC
Shelf Life 24 months from the date of
manufacture in the originalunopened container
Flashpoint >93ºC
Boiling point 38ºC

APPLICATION
Consult MSDS before proceeding Wear suitable gloves, goggles and protective clothing. Cover the lid with a cloth and hold away from face during
opening
Pour Paramose into a suitable container and replace top of can Apply a generous even coat by brush do not over brush Leave for between 20 - 40 minutes until the product reacts
with the paint or varnish. For multi layered surfaces (5 or more), a second coat of
Paramose AS10 is recommended. Use a dabbing motion,without the need to remove the .rst coat. Check at intervals to see how the AS10 is working and
remove softened paint with a scraper. Power wash clean with cold water.


© Chemicals Limited, PO Box 88, Southport, Merseyside PR8 5LH. Tel: 01704 880800. Fax: 01704 880900. BS EN ISO 9001:2008 Cert No: 4146865
VERSION 1 AUGUST 2018 FORM 34
STORAGE
Keep out of reach of children
Keep in a dry place between 5ºc and 30ºc in the original container.
IMPORTANT / LIMITATIONS
Read and follow the Health & Safety Data Sheets as detailed
in the separate MSDS document Ensure adequate ventilation at all times, DCM vapours are heavier than air so extractors should be at low level
Paramose AS10 must be shaken well before use
Always apply generous even coats
Do not try to spread she product too far, as this will result in
poor penetration and faster evaporation Allow Paramose AS10 to do its work Do not use in con.ned spaces Do not try to remove too quickly Never let the surface become too dry during treatment


CLEANING OF EQUIPMENT
Remove as much excess product as possible and clean tools and equipment immediately after use with soapy water.

COVERAGE
Coverage rates vary with porosity:
4-6m² per litre


PRECAUTIONS FOR USE
For Health & Safety instructions, .rst aid measures, spillages and disposal instructions, see separate Health & Safety Data Sheet (MSDS)
EUROPEAN REGULATIONS 455/2009/EC DICHLOROMETHANE PAINT REMOVERS ARE ONLY TO BE USED FOR INDUSTRIAL USE WHILST IN AN INDUSTRIAL ENVIRONMENT. The de.nition of Industrial is ‘Facilities where paint stripping takes place’.Examples would be units and workshops used for strippingarticles with either dip tanks or brush applied systems.

© Chemicals Limited, PO Box 88, Southport, Merseyside PR8 5LH. Tel: 01704 880800. Fax: 01704 880900. BS EN ISO 9001:2008 Cert No: 4146865